Copolymerization of Ethylene with Functionalized 1,1-Disubstituted Olefins Using a Fluorenylamido-Ligated Titanium Catalyst.

Considering the sustainability of material development, coordination polymerization catalysts effective for 1,1-disubstituted olefins are receiving a great deal of attention because they can introduce a variety of plant-derived comonomers, such as ß-pinene and limonene, into polyolefins. However, due to their sterically encumbered property, incorporating these monomers is difficult. Herein, we succeeded in the copolymerization of ethylene with various hydroxy- or siloxy-substituted vinylidenes using a fluorenylamido-ligated titanium catalyst-MMAO system. This is the first example of ethylene/polar 1,1-disubstituted olefins' copolymerization using an early transition metal catalyst system. The polymerization proceeded at room temperature without pressurizing ethylene, and high-molecular-weight, functionalized polyethylene was obtained. The obtained copolymer showed a reduced water contact angle compared with that of the ethylene/isobutene copolymer, demonstrating the increment in hydrophilicity by hydroxy groups.

Synthesis, Properties, and Biodegradability of Novel Sequence-Controlled Copolyesters Composed of Glycolic Acid, Dicarboxylic Acids, and C3 or C4 Diols.

We have previously reported that sequence-controlled copolyesters such as poly((ethylene diglycolate) terephthalate) (poly(GEGT)) showed higher melting temperatures than those of the corresponding random copolymers and high biodegradability in seawater. In this study, to elucidate the effect of the diol component on their properties, a series of new sequence-controlled copolyesters composed of glycolic acid, 1,4-butanediol or 1,3-propanediol, and dicarboxylic acid units was studied. 1,4-Butylene diglycolate (GBG) and 1,3-trimethylene diglycolate (GPG) were prepared by the reactions of 1,4-dibromobutane or 1,3-dibromopropane with potassium glycolate, respectively. Polycondensation of GBG or GPG with various dicarboxylic acid chlorides produced a series of copolyesters. Terephthalic acid, 2,5-furandicarboxylic acid, and adipic acid were used as the dicarboxylic acid units. Among the copolyesters bearing terephthalate or 2,5-furandicarboxylate units, the melting temperatures (Tm) of the copolyesters containing 1,4-butanediol or 1,2-ethanediol units were substantially higher than those of the copolyester containing the 1,3-propanediol unit. Poly((1,4-butylene diglycolate) 2,5-furandicarboxylate) (poly(GBGF)) showed a Tm at 90 °C, while the corresponding random copolymer was reported to be amorphous. The glass-transition temperatures of the copolyesters decreased as the carbon number of the diol component increased. Poly(GBGF) was found to show higher biodegradability in seawater than that of poly(butylene 2,5-furandicarboxylate) (PBF). On the other hand, the hydrolysis of poly(GBGF) was suppressed in comparison with that of poly(glycolic acid). Thus, these sequence-controlled copolyesters have both improved biodegradability compared to PBF and lower hydrolyzability than PGA.

Synthesis of Chain-End Functional Polydienes Using Diene Comonomer Bearing Boronic Acid Masked with Diaminonaphthalene.

Diene comonomers bearing boronic acid masked with 1,8-diaminonaphthalene (dan) were applied to copolymerization with isoprene or butadiene using neodymium borohydride complex as a catalyst. The comonomers were tolerant to excess modified methylaluminoxane (MMAO) and thus were applicable to the polymerization system using MMAO. On the other hand, the corresponding pinacol borate was highly reactive toward MMAO, and no incorporation into the obtained polymer was observed. A 13C NMR microstructural analysis of the hydrogenated copolymer revealed that all of the comonomers were located at the chain end. Further functionalization using the boron moiety at the polymer chain end was also investigated.

Synthesis, Properties, and Biodegradability of Thermoplastic Elastomers Made from 2-Methyl-1,3-propanediol, Glutaric Acid and Lactide.

An innovative type of biodegradable thermoplastic elastomers with improved mechanical properties from very common and potentially renewable sources, poly(L-lactide)-b-poly(2-methyl-1,3-propylene glutarate)-b-poly(L-lactide) (PLA-b-PMPG-b-PLA)s, has been developed for the first time. PLA-b-PMPG-b-PLAs were synthesized by polycondensation of 2-methyl-1,3-propanediol and glutaric acid and successive ring-opening polymerization of L-lactide, where PMPG is an amorphous central block with low glass transition temperature and PLA is hard semicrystalline terminal blocks. The copolymers showed glass transition temperature at lower than -40 °C and melting temperature at 130-152 °C. The tensile tests of these copolymers were also performed to evaluate their mechanical properties. The degradation of the copolymers and PMPG by enzymes proteinase K and lipase PS were investigated. Microbial biodegradation in seawater was also performed at 27 °C. The triblock copolymers and PMPG homopolymer were found to show 9-15% biodegradation within 28 days, representing their relatively high biodegradability in seawater. The macromolecular structure of the triblock copolymers of PLA and PMPG can be controlled to tune their mechanical and biodegradation properties, demonstrating their potential use in various applications.

Synthesis, Properties, and Biodegradation of Sequential Poly(Ester Amide)s Containing γ-Aminobutyric Acid.

Poly(ester amide)s are attracting attention because they potentially have excellent thermal and mechanical properties as well as biodegradability. In this study, we synthesized a series of novel poly(ester amide)s by introducing γ-aminobutyric acid (GABA) regularly into polyesters, and investigated their properties and biodegradabilities. GABA is the monomer unit of biodegradable polyamide 4 (PA4). The new poly(ester amide)s were synthesized from the reaction of ammonium tosylate derivatives of alkylene bis(γ-aminobutylate) and p-nitrophenyl esters of dicarboxylic acids. All the obtained polymers showed relatively high melting temperatures (Tm). Their thermal decomposition temperatures were improved in comparison with that of PA4 and higher enough than their Tm. The poly(ester amide)s exhibited higher biodegradability in seawater than the corresponding homopolyesters. Their biodegradabilities in activated sludge were also studied.

Impregnation of poly(L-lactide-ran-δ-valerolactone) with essential bark oil using supercritical carbon dioxide.

This work studied the incorporation of essential bark oil from Thujopsis dolabrata var. hondae, which is known to repel various insects, in poly(L-lactide-ran-δ-valerolactone) [poly(L-LA-ran-VL)] using supercritical carbon dioxide (scCO2). The poly(L-LA-ran-VL) was synthesized by first purifying the monomers by azeotropic distillation with benzene, followed by polymerization with Sn(oct)2 using the same equipment, representing an efficient one-pot process. The copolymerization of L-LA with VL using this technique at a feed ratio of 90/10 mol/mol gave poly(L-LA-ran-VL) (91/9) with a molecular weight of 6.48 × 104 g/mol and a high yield of 74.9%. Products with molecular weights over 5.0 × 104 g/mol were obtained at L-LA feed proportions of 70 to 90%. Impregnation trials were conducted between 40 and 120 °C at 14 MPa for 3 h. The oil content of a 73/27 specimen was found to increase significantly during processing at 100 or 120 °C. During enzymatic degradation with proteinase K, the 91/9 specimen showed the fastest degradation rate. Although the 71/29 sample was slowly hydrolyzed in a phosphate buffer at pH 7.0, the release of oil vapor from this material was slightly higher than that from the 91/9 specimen, and the vapor release rate continuously increased throughout the hydrolysis process.

Copolymerization of Norbornene and Styrene with Anilinonaphthoquinone-Ligated Nickel Complexes.

Poly(norbornene-co-styrene)s were synthesized by the use of anilinonaphthoquinone-ligated nickel complexes [Ni(C10H5O2NAr)(Ph)(PPh3): 1a, Ar = C6H3-2,6-iPr; 1b, Ar = C6H2-2,4,6-Me; 1c, Ar = C6H5] activated with modified methylaluminoxane (MMAO) or B(C6F5)3 in toluene. The effects of the cocatalysts were more significant than those of the nickel complexes, and MMAO gave higher activity than B(C6F5)3. The structural characterizations of the products indicated the formation of statistical norbornene copolymers. An increase of the styrene ratio in feed led to an increase in the incorporated styrene (S) content of the resulting copolymer. The molecular weight of the copolymer decreased with increasing the S ratio in feed at 70 °C. The copolymerization activity, using MMAO as a cocatalyst, decreased with lowering of the temperature from 70 to 0 °C, accompanied by an increase in the molecular weight of the copolymer. The S incorporation up to 59% with Mn of 78,000 was achieved by the 1b-B(C6F5)3 catalytic system. The glass transition temperatures of the norbornene (N)/S copolymers determined by differential scanning calorimetry, decreased from 329 to 128 °C according to the S content.

Stereospecific polymerization of conjugated dienes using neodymium alkylborohydride complexes.

Two neodymium alkylborohydride complexes that differ with respect to the number of hydrides on the boron center were synthesized and characterized. The µ2-ligated complex exhibits Nd-B bond lengths that are approximately 10% longer than those in previously reported µ3-ligated borohydride complexes. For the µ3-alkylborohydride complex, the Nd-H-B stretching bands observed by IR spectroscopy suggested stronger borohydride coordination than that of [BH4]-, which is probably due to the electron donation of the alkyl groups. These newly prepared complexes successfully promoted trans-1,4 specific polymerization of conjugate dienes upon activation by Bu2Mg, whereas activation of these complexes by Bu2Mg/MMAO gave cis-1,4 regular polymer. The trans-1,4 defect of the polyisoprene obtained from the Nd µ2-alkylborohydride complex/Bu2Mg/MMAO system (<2%) was much lower than that obtained from previously reported µ3-BH4-ligated neodymium complex (11%). Moreover, µ2-alkylborohydride complex was a good initiator for the polymerization of MMA, probably because of its anionic nature.

Synthesis and Biodegradation of Poly(l-lactide-co-ß-propiolactone).

Although the copolymerizations of l-lactide (LA) with seven- or six-membered ring lactones have been extensively studied, the copolymerizations of LA with four-membered ring lactones have scarcely been reported. In this work, we studied the copolymerization of LA with ß-propiolactone (PL) and the properties of the obtained copolymers. The copolymerization of LA with PL was carried out using trifluoromethanesulfonic acid as a catalyst and methanol as an initiator to produce poly(LA-co-PL) with Mn of ~50,000 and PL-content of 6-67 mol %. The Tg values of the copolymers were rapidly lowered with increasing PL-contents. The Tm and ΔHm of the copolymers gradually decreased with increasing PL-contents, indicating their decreased crystallinity. Biodegradation test of the copolymers in compost demonstrated their improved biodegradability in comparison with the homopolymer of LA.

Precision Chain-Walking Polymerization of trans-4-Octene Catalyzed by α-Diimine Nickel(II) Catalysts Bearing ortho-sec-Phenethyl Groups.

α-Diimine nickel complexes bearing bulky ortho-sec-phenethyl groups (bis{[N,N'-(4-methyl-2,6-di-sec-phenethylphenyl)imino]-1,2-dimethylethane}dibromonickel (1), bis{[N,N'-(4,6-dimethyl-2-sec-phenethylphenyl)imino]-1,2-dimethylethane}dibromonickel (2), bis{[N,N'-(4-methyl-2-sec-phenethylphenyl)imino]-1,2-dimethylethane}dibromonickel (3)) and {bis[N,N'-(2,4,6-trimethylphenyl)imino]-1,2-dimethylethane}dibromidonickel (4) are used as a precatalyst for the polymerization of trans-4-octene upon activation with modified methylaluminoxane. These catalysts conduct chain-walking polymerization of trans-4-octene to give polymers possessing propyl and butyl branches with high molecular weight and narrow molecular weight distribution. The branching structure depends on the nickel complex as well as the polymerization temperature, and the ratio of propyl branch was increased with increasing the bulkiness of the ligand and decreasing the polymerization temperature. Consequently, the most bulky 1 among the complexes used is found to polymerize trans-4-octene with high 1,5-regioselectivity at -20 °C to give poly(1-propylpentan-1,5-diyl).

Synthesis of Highly Branched Polyolefins Using Phenyl Substituted α-Diimine Ni(II) Catalysts.

A series of α-diimine Ni(II) complexes containing bulky phenyl groups, [ArN = C(Naphth)C = NAr]NiBr2 (Naphth: 1,8-naphthdiyl, Ar = 2,6-Me2-4-PhC6H2 (C1); Ar = 2,4-Me2-6-PhC6H2 (C2); Ar = 2-Me-4,6-Ph2C6H2 (C3); Ar = 4-Me-2,6-Ph2C6H2 (C4); Ar = 4-Me-2-PhC6H3 (C5); Ar = 2,4,6-Ph3C6H2 (C6)), were synthesized and characterized. Upon activation with either diethylaluminum chloride (Et2AlCl) or modified methylaluminoxane (MMAO), all Ni(II) complexes showed high activities in ethylene polymerization and produced highly branched amorphous polyethylene (up to 145 branches/1000 carbons). Interestingly, the sec-butyl branches were observed in polyethylene depending on polymerization temperature. Polymerization of 1-alkene (1-hexene, 1-octene, 1-decene and 1-hexadecene) with C1-MMAO at room temperature resulted in branched polyolefins with narrow Mw/Mn values (ca. 1.2), which suggested a living polymerization. The polymerization results indicated the possibility of precise microstructure control, depending on the polymerization temperature and types of monomers.

Highly Active Syndiospecific Living Polymerization of Higher 1-Alkene with ansa-Fluorenylamidodimethyltitanium Complex.

1-Hexene polymerization was conducted by [t-BuNSiMe(2) (3,6-t-Bu(2) Flu)]TiMe(2) (1) using trialkylaluminum-free modified methylaluminoxane (dMMAO) as a cocatalyst in toluene. The system produced living syndiotactic poly(1-hexene) with high turnover frequency of propagation (TOF, 98 s(-1) ) at 0 °C. The propagation rate was increased linearly against the 1-hexene concentration, which indicates that the first-order dependence of the propagation rate on monomer concentration. Polymerizations of 1-octene, 1-decene and 1-dodecene were also conducted for investigating the effect of chain length of 1-alkene on propagation rate by means of the livingness of this system. The propagation rate decreased according to the chain length until 1-decene but almost unchanged in longer 1-alkene: TOF, 1-octene (62 s(-1) )>1-decene (32 s(-1) ) ≈ 1-dodecene (31 s(-1) ).

Developments of chiral metallocenes as polymerization catalysts.

This review article describes developments in chiral metallocenes as polymerization catalysts focusing on C2 symmetric ansa-zirconocene complexes. Selective synthesis of rac-isomers of ansa-zirconocenes are surveyed. Isospecific polymerizations of propylene catalyzed by chiral zirconocenes are summarized. Advanced series of polymerizations by chiral metallocenes such as asymmetric polymerization and polymerization of polar monomers are also introduced.

Synthesis of Arenethiolate Complexes of Divalent and Trivalent Lanthanides from Metallic Lanthanides and Diaryl Disulfides: Crystal Structures of [{Yb(hmpa)(3)}(2)(&mgr;-SPh)(3)][SPh] and Ln(SPh)(3)(hmpa)(3) (Ln = Sm, Yb; hmpa = Hexamethylphosphoric Triamide).

A convenient and one-pot synthetic method of lanthanide thiolate compounds was developed. An excess of metallic samarium, europium, and ytterbium directly reacted with diaryl disulfides in THF to give selectively Ln(II) thiolate complexes, [Ln(SAr)(&mgr;-SAr)(thf)(3)](2) (1, Ln = Sm; 2, Ln = Eu; Ar = 2,4,6-triisopropylphenyl), Yb(SAr)(2)(py)(4) (3, py = pyridine), and [{Ln(hmpa)(3)}(2)(&mgr;-SPh)(3)][SPh] (6, Ln = Sm; 7, Ln = Eu; 8, Ln = Yb; hmpa = hexamethylphosphoric triamide). Reaction of metallic lanthanides with 3 equiv of disulfides afforded Ln(III) thiolate complexes, Ln(SAr)(3)(py)(n)()(thf)(3)(-)(n)() (9a, Ln = Sm, n = 3; 9b, Ln = Sm, n = 2; 10, Ln = Yb, n = 3) and Ln(SPh)(3)(hmpa)(3) (11, Ln = Sm; 12, Ln = Eu; 13, Ln = Yb). Thus, Ln(II) and Ln(III) thiolate complexes were prepared from the same source by controlling the stoichiometry of the reactants. X-ray analysis of 8 revealed that 8 has the first ionic structure composed of triply bridged dinuclear cation and benezenethiolate anion [8, orthorhombic, space group P2(1)2(1)2(1) with a = 21.057(9), b = 25.963(7), c = 16.442(8) Å, V = 8988(5) Å(3), Z = 4, R = 0.040, R(w) = 0.039 for 5848 reflections with I > 3sigma(I) and 865 parameters]. The monomeric structures of 11 and 13 were revealed by X-ray crystallographic studies [11, triclinic, space group P&onemacr; with a = 14.719(3), b = 17.989(2), c = 11.344(2) Å, alpha = 97.91(1), beta = 110.30(2), gamma = 78.40(1) degrees, V = 2751.9(9) Å(3), Z = 2, R = 0.045, R(w) = 0.041 for 7111 reflections with I > 3sigma(I) and 536 parameters; 13, triclinic, space group P&onemacr; with a = 14.565(2), b = 17.961(2), c = 11.302(1) Å, alpha = 97.72(1), beta = 110.49(1), gamma = 78.37(1) degrees, V = 2706.0(7) Å(3), Z = 2, R = 0.031, R(w) = 0.035 for 9837 reflections with I > 3sigma(I) and 536 parameters]. A comparison with the reported mononuclear and dinuclear lanthanide thiolate complexes has been made to indicate that the Ln-S bonds weakened by the coordination of HMPA to lanthanide metals have ionic character.